hostno.blogg.se

1. Digital persona fingerprint reader software windows 10 tool install#
2. Digital persona fingerprint reader software windows 10 tool driver#
3. Digital persona fingerprint reader software windows 10 tool registration#
4. Digital persona fingerprint reader software windows 10 tool Pc#

Why? Older readers sometimes blink if there is a buildup of dust on the fingerprint window area.

Digital persona fingerprint reader software windows 10 tool Pc#

Refer to the documentation that came with your PC for instructions.Ħ The reader light keeps blinking. Go into your system BIOS and make sure that the USB settings are set to enable. If you still have problems, it is most likely that the USB hardware is not setup correctly.

Digital persona fingerprint reader software windows 10 tool driver#

Remove the U.are.U fingerprint device driver from Biometric or Scanning Device section. From the Control Panel, go to System, go to Device Manager. Try the following: Disconnect the reader. If you plug in the reader as instructed but see no activity, this indicates that either your USB port is not setup correctly or the Windows Found New Device Wizard did not recognize the reader. The red light on the reader should turn on and you can continue with the installation. The dialog box will disappear when it is finished.

The Windows Found New Device Wizard dialog box should appear, informing you that it has detected a new device and that it will automatically find all the necessary drivers. Once the reader is plugged in, you should see some activity on your monitor. Why? In a normal installation, the setup will prompt you to plug in the reader. During the software installation, setup prompted me to plug in the reader. If you have cold hands, try warming your scanning finger by holding or blowing on your finger. You must use the same finger you successfully registered when initially logging into the system 5. Make sure you are using the correct finger. The best way to do this is with a piece of tape. Pressing too long or too hard can cause a reading error. If you have dry hands, try applying lotion before scanning. If the scanner cannot read your fingerprint, the system will tell you the information you have entered is not correct. I have a registered fingerprint, but I m having trouble logging in why? If you are having issues logging into the system, here are some tips to help get a good fingerprint scan. If this does not help, try registering your fingerprint again or using a different finger. Using hand lotion or rubbing your finger on your forehead before placing it on the reader sometimes helps. Also, dry fingers sometimes cause the reader to fail. The recommended method to register fingerprints is to use one of the last three fingers (middle, ring, or pinky finger) on your non-dominant hand. Why doesn t the system recognize my fingerprint? Sometimes fingerprints can be more worn on fingers that are primarily used. Try reinstalling the fingerprint reader if it still shows Service Unavailable at the login screen. Try closing all browser windows and attempt again, you may need to clear your browser cookies. Make sure the computer system requirements and web browser are compatible with the fingerprint reader.

Digital persona fingerprint reader software windows 10 tool install#

Why does the login screen show Service Unavailable under the password field? Either the fingerprint reader did not install properly or the web browser is not recognizing the installed reader. If you have any web filtering or other Internet browser security measures in place you may need contact your IS department to make sure you are not being blocked. Make sure to disable any pop-up blockers for this site. Enter your username and password and touch the fingerprint recognition device and you will now have access to the system.ĥ Fingerprint Reader FAQ and Troubleshooting Guide I click on Register to register a new Fingerprint and nothing happens? You should see a new screen for Fingerprint Enrollment. Click on the link that says, Click here to return to the Login Page and you will be returned to the main system login page. Once you have successfully registered your finger, you will be returned to the Fingerprint Authentication Management screen with a message stating you have successfully registered your fingerprint. This is generally four times but may be more if the system does not properly read your fingerprint. You will be asked to repeatedly touch the fingerprint device until the system has successfully registered your finger.

This will move you to the next step, which is displayed below. Choose the finger you wish to register by clicking the finger on the screen.

Digital persona fingerprint reader software windows 10 tool registration#

You will be presented with the Registration screen below. 4 To register your finger with the system, click Register.